Applications are invited for SUMMER INTERNSHIP PROGRAM for B-TECH / I.T.I. students

BTS Installation


Takshak Telecom also provide the service of BTS installation and BTS maintinance.Takshak Telecom provide services in BTS installation and maitinance are:

1.Radio Power Management

2.Voltage Standing Wave Ratio (VSWR) Measurement for RF feeder cables.

3.Verification and correction of Connectorization of RF / IF cables.

4.Validation of antenna orientations and corrections if required.

5. Preventive Maintenance services as per the SLA / SOW.

6. Corrective Maintenance

7. DG servicing, AC servicing and Over Hauling in accordance with the specification by OEM / Customer.

8. Break down Maintenance like tracking of Alarms for site outages and link failures.

9. Diesel filling according to the BEET PLAN to ensure the availability of HSD in the DG tank.

10. Power Plant

11. Diesel Generator

12. PMU (Power Management Unit)

13. Fire Alarm System

14.Battery Bank

15. Air Conditioners

16.Shelters

17. Servo Stabilizers

18. SMPS

19. Tower / Mast / Pole

20. Earth Pits

21. Other Electrical Elements







Installation & Commissioning of BTS Equipment



Scope of work


1.Receipt of site information from customer along with TND/RND

2.RFI check along with ensuring the site permissions

3.Material reception at the sites and checking as per packing list. Intimate to the customer in case of any deficiency

4.Hoisting of GSM/CDMA antennas on tower as per TND/RND

5.Clamping and routing of RF cables from Shelter to Antennae

6.Grounding the Antennae and RF cables at appropriate place

7.Ensuring drip loop/Z loop at cable entry plate

8.Ensuring no sharp bend on RF cables

9.Fixing OGB

10.Weather proofing

11.Fixing EMPs/Surge arrestors along with connectorization in shelter

12.Grouting the BTS

13.Extending, power cables, E1 cables, grounding cables to BTS

14.Fixing IGB and extending grounding to all peripheral equipment

15.Fixing DDF

16.Installation of Battery bank and rectifier

17.Installation of internal cable try

18.Installation of indoor jumpers

19.Checking VSWR

20.Switching on the equipment

21.Commissioning the equipment as per defined procedure

22.Power measurement

23.Filling the check list and execution of quality audit






MW Installation and commissioning



Scope of works:

*Receipt of site information from customer along with TND/RND.

*RFI check in near end and far end besides ensuring the site permissions.

*Material reception at both ends and checking as per packing list and intimate the customer in case of exigency.

*Assembling and hoisting of MW antennas & radios on tower in both ends as per TND/RND.

*Clamping and routing of if cables from Shelter to Antennae in both ends.

*Grounding the antennas and RF cables at appropriate place.

*Fixing Transmission rack if required in both ends.

*Installation & commissioning of IDUs in shelters.

*Alignment of MW antennas till we achieve required receive level,

*Grounding, weather proofing and labeling all cables in both ends.

*Acceptance test






BSC/MSC/STP/SDH/DWDM/PTN/XDM/DLC/FSO/DSLAM Installation and commissioning



Scope of works:

*Receipt of site information from customer along with TND/RND.

*RFI check at the site besides ensuring the site permissions. Sending the SDR to customer.

*Material reception and checking as per packing list and intimate the customer in case of exigency.

*Grouting the equipment rack and inserting all required modules as per the manual/lay out drawing.

*Interconnection with appropriate cables/jumpers.

*Grounding the equipment.

*Installation of DCDB and extension of power to the equipment.

*Installation of DDF and extension of E1s to the equipment by Kroning.

*Installation of optical cables if required and measurement of power.

*Switching on the equipment and commissioning as per the procedure.

*Allotment of given IP address and extension of services to the subscribers.

*BER test if required.

*Preparation of AT document and sign off.